P retty, feminine card that would work for a birthday or Valentine's Day using Stampin' Up! products.
Project Recipe
Cut cardstock and designer paper pieces to the following sizes using a Stampin' Trimmer:
- card from Flirty Flamingo Cardstock at 5-1/2" x 8-1/2" and scored at 4-1/4"
- 3-3/8" x 4-5/8" from Lovely Lipstick Cardstock
- 3-1/4" x 4-1/2" from Whisper White Cardstock
- 1-1/4" x 3-1/4" of scattered pink flowers and light green leaves outlined in white on light pink background from All My Love Designer Series Paper
- 3/4" x 4" of scattered pink and red flowers and light green leaves outlined in white on brown background from All My Love Designer Series Paper
- small red flower hand cut from scattered pink and red flowers and light green leaves outlined in white on brown background from All My Love Designer Series Paper
As you are ready to stamp using the Incredible Like You Set, place the cardstock on the Stampin' Pierce Mat. Using the mat will help you get a cleaner image each time you stamp
Mount the "I just adore you," "hope your day is a amazing as you," or "incredibly proud of you" sentiment from the Incredible Like You Set on Block H. Ink it up with the Lovely Lipstick Ink Pad. Stamp it on the right side of the piece of white cardstock so it is about 1-1/8" from the top.
Start building this sandwich in this order on top of the Big Shot:
- Big Shot Platform with Thin Die Adapter removed
- white Impressions Pad from Big Shot Embossing Mats
- thinner blue silicone rubber mat from Big Shot Embossing Mats
- sentiment stamped white rectangle
Pick out the straight edged heart with no stitching framelit that cuts out a heart that is 2-1/4" wide from the Be Mine Stitched Framelits.
Place the heart framelit cutting edge down on top of the open Flirty Flamingo Ink Pad. Place a piece of copy paper on top and rub firmly all over.
Carefully remove the copy paper and the inky heart framelit from the ink pad.
Carefully place the inky heart framelit, cutting side down, on top of the sentiment stamped white cardstock on the Big Shot so the framelit is centered over the stamped sentiment. Place a Standard Cutting Pad (clear pad) on top and run it through the Big Shot.
Carefully remove everything from the Big Shot.
Tip: You should have a dry embossed, pink outlined heart around the sentiment on the white cardstock.
Tip: Immediately run the framelit under water to remove all ink and dry it off with a towel.
Adhere the larger piece of pink background All My Love Designer Series Paper to the left side of the stamped and dry embossed white layer.
Adhere the white/designer paper layer to the Lovely Lipstick layer and then to the center of the front of the Flirty Flamingo card.
Cut a 1-1/4" piece of the Flirty Flamingo 1/8" ribbon from the All My Love Ribbon Combo Pack.
Lay the ribbon across the skinny strip of brown background All My Love Designer Paper about 1-1/4" from the bottom. Flip the layers over and fold the ends of the ribbon over. Adhere the ends of the ribbon in place with pieces of Tear & Tape Adhesive.
Remove the protective backing from the Tear & Tape strips and add SNAIL to the back of the designer paper strip. Adhere it to the front of the card so it is centered top to bottom and overlaps the right edge of the pink background layer of designer paper.
Cut an 8" piece of Flirty Flamingo 1/8" ribbon from the All My Love Ribbon Combo Pack.
Tie a bow in the center of the ribbon. Trim the ends.
Use a Mini Glue Dot to adhere the ribbon bow to the right side of the ribbon already on the card front at a slight angle.
If you haven't already done so, use Paper Snips to cut a small red flower from a scrap of the brown background All My Love Designer Series Paper.
Use a Mini Stampin' Dimensional to adhere the cut out flower to the front of the card on the lower right side of the dry embossed heart.